This entirely depends on the company and/or the type of work you do. My manager is considering implementing it after I proposed it for our team. That was only a few days ago so we’ll see where it goes.
This entirely depends on the company and/or the type of work you do. My manager is considering implementing it after I proposed it for our team. That was only a few days ago so we’ll see where it goes.
I don’t remember for sure about the old games, but the Legendary Edition has one for each game.
Interesting. The only two references I’ve ever heard to Paramour are the band and the achievement in Mass Effect. I’m now wondering if the devs of that series knew exactly what it meant (infidelity) because you get the achievement for having any relationship. Maybe it’s because you can’t remain loyal to your original partner to get it in all three games with one playthrough.
I’d love to experience the Mass Effect trilogy for the first time again. Especially since I started with 3 so I already knew the ending when I went back to the other games.
I don’t remember the first song I played, but I remember blasting Eminem’s “Without Me” at full volume with my new 12-inch subwoofer from Walmart. An officer pulled up next to me and my teenage self just about shit a brick. He just started nodding to the beat and drove off.
Maybe Eminem’s “Shake That?”
This happens to me with Xbox controllers randomly. 90% of the time they work, but then I randomly need to re-pair, reboot the Deck, toggle Bluetooth (any of these make it work again), or grab a different controller.
That’s what I imagined I’d see or hear and I’m not seeing any of that. I’ll take a closer look again though now that I know for sure. Thanks!
Not that I’m aware of as I don’t hear any odd noise from the extruder or see marks on the filament. I’m new to this though so I probably don’t know what to look for. What told you that yours was slipping?
I played around with retraction a bit, but I’ll give that another shot. Thanks for the input.
It seems to be randomly within a layer rather than at the start and changes to retraction don’t seem to improve it. Oddly enough, I’m noticing on a more recent print that it seems to happen more frequently within supports (generated by Cura), which I think are printed faster.
I’ll try drying the filament. All of my Creality filament is from Amazon, where as the Inland stuff is all from my local Micro Center. I wonder if the filament from Amazon is just sitting around for a while, or in poor conditions.
I mostly do my own work, but whenever I do take my car to the local Mazda dealer, they always provide a full inspection report as well as a video of the tech checking everything and explaining anything that they’ve found. Even when my wife takes her car in for only basic maintenance (it’s still under warranty so we take it in for oil changes), they do the same thing and don’t charge anything extra.
Same dealer network owns the local Ford dealer and I ended up taking my old Fiesta ST there for an oil change as I didn’t have the space to do it myself at the time. $45 for an oil change and tire rotation, and I got the same inspection report and video.
A while ago, there was something that showed the higher failure rate of various components on EVs because of the lack of routine service that has cars have. Basically, gas cars get a service and inspection every 5-10k miles when the oil is changed and any worn bearings, bushings, etc. are found. EVs don’t have that so things go unnoticed until they fail. Could this be the same? Could the “reliability” concerns just be normal wear that isn’t getting caught since there are no routing inspections?
Where did you get the driver for it?
Damn. Oh well. Good to know though. Thanks!
This is interesting as I’m looking for the opposite answer. I want my Deck to wake up when I turn on my Xbox controller, but it doesn’t right now unless I wake it up with the power button first. If you find something outside of this thread, please let me know.
Is this only in certain areas? YouTube is still working fine for me on FireFox.
It’s not an employee benefit. It’s a membership thing that customers can sign up for. It was literally the only perk of it.
Yes! I miss my r/Triumph and r/KLR650. Also missing r/Miata.
I had something like this happen to me recently on my Ender 3 Max Neo. My filament feeds from a separate dry box and the spool was slightly crooked. Once the angle from the box to the extruder got too severe, the spool bound up and wouldn’t feed anymore. Moving the spool so it properly rested on the rollers fixed it.